Barrier coating for structures made with WEST SYSTEM epoxy

Once you have assembled your components and bonded them together, it is time to apply a protective barrier coat to prepare the structure for final finishing.

The object of barrier coating is to build up an epoxy thickness. This will provide an effective moisture barrier and a smooth base for final finishing.

This page covers:

How to apply an epoxy barrier coating
How to apply extra coats
How many extra coats to apply and when to use additives
Barrier coating tools
Barrier coating for osmosis repair

How to apply an epoxy barrier coating

1. Prepare the surface for bonding

2. Mix a limited amount of epoxy only

Mix only as much resin/hardener as can be applied during the open time of the mix. Mix the epoxy thoroughly then pour into a roller pan.

3. Load the roller with a moderate amount of the epoxy

Roll out the excess on the raised section of the roller pan to make sure there is a uniform coating round the roller.

4. Roll lightly and randomly

This will transfer the epoxy evenly over an area of approximately 600mm x 600mm.
ORG 24
Roll lightly and randomly over a small area. Spread the epoxy into thin even film

5. Spread the epoxy into a thin even film

As the roller dries out, increase pressure to spread the epoxy into a thin even film. Increase the coverage area if necessary to spread the film more thinly and evenly. The thinner the film, the easier it is to keep it even and it will also be easier to avoid runs or sags in each coat.

6. Finish the area with long, light, even strokes to reduce roller marks

Overlap previously coated areas with newly coated areas to blend both areas together.

7. Coat as many of these small working areas as possible with each batch

If a batch begins to thicken before it can be applied, discard it and mix a fresh, smaller batch.

8. 'Tip off' the coating

Do this  by dragging a foam roller brush lightly over the fresh epoxy in long, even, overlapping strokes after each batch is applied. Use enough pressure to smooth the 'stipple', but not enough to remove any of the coating. Alternate the direction in which each coat is tipped off. For example, for the 1st coat, move vertically, for the 2nd, horizontally, for  3rd coat vertically and so on. A WEST SYSTEM® 800 Roller Cover can be cut into segments to make an excellent 'tipping' brush.
ORG 25
Tip off the coating by dragging a foam roller brush lightly over the fresh epoxy.

How to apply extra coats

Apply the second and any subsequent coats of epoxy by following the same procedures. Ensure that the previous coat is still tacky but has also cured firmly enough to support the weight of the next coat. To avoid sanding between coats, it is best to apply all coats in the same day. After the final coat has cured overnight, wash with clean water and abrade the surface to prepare for the final finish.

Complete all fairing and cloth applications before beginning the final coating. Allow the temperature of porous surfaces to stabilise before coating. If you do not leave enough time for this, the material will warm up and air within the porous material may expand and pass from the material through the coating. This so-called 'out-gassing' may leave bubbles in the cured coating.

How many extra coats to apply and when to use additives

Apply a minimum of two coats of WEST SYSTEM epoxy for an effective moisture barrier. Moisture protection will increase with additional coats.

Apply three coats if sanding is to be carried out.

Apply six coats, or about a thickness of 600 microns for osmosis repair and protection.

Six coats, with 422 Barrier Coat Additive in the final five coats, provides maximum moisture protection. Additives or pigments should not be added to the first coat. Also, do not add thinners or solvents to WEST SYSTEM epoxy.

Barrier coating tools

Disposable, thin urethane foam rollers, such as WEST SYSTEM 800 or 790 Roller Covers, allow greater control over film thickness, are less likely to cause the epoxy to exotherm and leave less stipple than thicker roller covers. If you're struggling to reach difficult areas, cut the covers into narrower widths. A paint brush can be used for smaller areas if the bristles are stiff enough to spread the epoxy to an even film.

Barrier coating for osmosis repair

Osmosis, otherwise known as gel-coat blistering, is a complex phenomenon that affects boat hulls. Before starting any treatment, we strongly recommend seeking the advice of a qualified marine surveyor with experience in osmosis repair. Specialist boatyards or contractors will be able to obtain a full report from a surveyor before starting work on the hull.

Hull constructions are very varied so there is no way to guarantee long-term 100% success after a repair.

 

 

Subscribe to our newsletter so we can share with you our unique knowledge and experience of working with epoxy.

 

 

New Downloads

Latest PRO-SET news - Autumn 2017

Guide to osmosis repair
For detailed information on minimising the risk of recurring osmosis damage, click here to download our specialist manual Gelcoat Blisters – A guide to osmosis repair.

Demonstration video
Watch our instructional video here to see our Technical Expert demonstrate how to apply a barrier coat to your structure.

Explore our accessories
A number of WEST SYSTEM tools and accessories have been specially designed to suit the barrier coat application techniques explained above. To explore the full range of brushes, rollers and more, click here.

Our site uses cookies and similar technologies.

By clicking on the button below you agree to the cookies being used on this site. Learn more

I understand

Use of Cookies

Cookies provide information regarding the computer used by a visitor. We may use cookies where appropriate to gather information about your computer fin order to assist us in improving our website.

We may gather information about your general internet use by using the cookie.  Where used, these cookies are downloaded to your computer and stored on the computer’s hard drive. Such information will not identify you personally. It is statistical data. This statistical data does not identify any personal details whatsoever

You can adjust the settings on your computer to decline any cookies if you wish.  This can easily be done by activating the reject cookies setting on your computer.

Our advertisers may also use cookies, over which we have no control.  Such cookies (if used) would be downloaded once you click on advertisements on our website.

See our Privacy policy for more information